Bonderite C-IC Zinctone (378337) is a clear, red liquid formulated to remove light oxide films and brighten zinc and zinc alloy parts, such as carburettors fuel pumps and die-cast by immersion methods. The product dramatically brightens brass and copper alloys. Bonderite C-IC Zinctone (378337) restores the original lustre to zinc alloys, and is frequently used on zinc components that require visible and fluorescent penetrant inspection prior to re-assembly and for penetrant inspection of raw zinc die castings prior to machining.
Bonderite C-SO 4460 (378341) is a water-white liquid formulated to replace methyl ethyl ketone and similar type solvents that are environmentally unacceptable due to their high composite vapour pressures. Bonderite C-SO 4460 (378341) is ideal for hand-wipe cleaning of metal surfaces prior to painting, bonding and for cleaning bearings, instruments and electronic components.
Bonderite M-MN 112 (1234915) can be run at a lower temperature range if Accelerator 131 is used in the bath operation. Bonderite M-MN 112 (1234915) is formulated to produce non-metallic, oil-absorptive coatings on iron and steel bearing surfaces. These corrosion-resistant coatings consist chiefly of iron and manganese phosphates, and reduce wear on such articles as pistons, rings, liners, camshafts, tappets, motor blocks and similar bearing surfaces.
Bonderite M-PT 99 (168829) post treatment chemical is a patented, chromium free post treatment especially formulated for use over conversion coatings. The post treatment is free of volatile organic components and increases the corrosion resistance of painted metal surfaces. Bonderite M-PT 99 (168829) is a reactive, resin based post treatment chemical, containing no heavy metals. Its corrosion resistance performance is equal to that of chromium containing post treatments. The treatment solution may be applied by spray application or by immersion application under ambient conditions and is followed by a deionised water rinse.
Bonderite C-IC 5600 (169835) is a non-chromated liquid desmutter and deoxidiser especially recommended for use in areas where chromated materials cannot be used because of sewage disposal limitations.Bonderite C-IC 5600 (169835) gives rapid desmutting and deoxidising on all wrought and extruded aluminium alloys.
Bonderite C-IC 624 (169370) is a phosphoric acid and solvent type metal cleaner and conditioner designed for manual application, which removes rust, destroys rusting agents and leaves the metal surface chemically clean and ready for painting.
COLORMAX 9000L is a new generation electrolytic colour bath, liquid concentrate. COLORMAX 9000L, with its unique and high quality ingredients, provides excellent throwing power and optimum colour uniformity. COLORMAX 9000L provides rich, deep colors, in shorter time than normally obtained from conventional coloring baths. COLORMAX 9000L is designed to be used with stainless steel or graphite counter electrode systems. Aluminum is first anodized in a controlled sulphuric acid electrolyte, under proper conditions. Consequently the anodized aluminum is treated in a COLORMAX 9000L bath using an AC power source to achieve a wide spectrum of colours ranging from champagne to black in minimum coloring time.
Bonderite C-SO Carbolene (168586) is a two-phase solvent product. The lower active phase contains a powerful solvent activated with special additives to promote rapid removal of carbon deposits and paint films. The upper aqueous phase contains corrosion inhibitors and also prevents evaporation and loss of efficiency of the solvent phase.
Bonderite C-IC 33 (169315) is an acidic metal cleaner and conditioner expressly compounded for aluminium. Prepares aluminium and its alloys for painting or welding. Bonderite C-IC 33 (169315) removes light deposits of oil and grease, mill markings and corrosion products, as well as natural oxide. Neutralises corrosion inducing materials such as welding or brazing fluxes and perspiration residues. Effectively removes corrosion products or stains, resulting from weathering, leaves the aluminium surface receptive for additional protection afforded by Alodine 1OOOL or 1200L or clear lacquers or waxes. Maximum protection of aluminium is afforded through the use of Alumlprep 33 (to clean and brighten), treatment with Alodlne No.1000L or 1200L (for corrosion resistance) and the application of clear lacquer or wax.
Bonderite M-NT 5200 MU treatment is a chromium free product and specifically formulated for treating aluminium and its alloys. Spray or immersion application may be used. The process provides an excellent base for organic finishes.
Bonderite M-CR 1132 Aero (38866) no-rinse conversion coating effectively phosphates most metals including aluminum, ferrous and galvanized substrates. Doesnt require rinsing, and can be air dried or force dried with hot air or an infra-red lamp. High density acrylic tip of the applicator can be modified with a single edge razor blade to form any shape. The application method controls the amount of coating applied to the surface.
Bonderite 600 M-CR Aero RTU (1939170) is a powdered chemical used in an aqueous solution to produce on aluminium or aluminium alloys a protective coating which ranges in colour from light, iridescent golden to tan. The coating produced provides excellent protection for unpainted aluminium and bonds paint well. It is particularly recommended where a low dielectric resistance coating is desired. Bonderite 600 M-CR Aero RTU (1939170), being listed on the Qualified Product List QPL-81706, is an approved material to be used by Method B (brush processing) to produce Class 3 coatings, bare or painted, in accordance with Military Specification MIL-C-5541E. It is applied using an acid-resistant brush, a swab, a synthetic sponge, or portable spray equipment, e.g., a paint spray gun or insect sprayer. The brush method of application is used when: 1. The number of pieces processed per day is not large, or 2. The parts to be treated are too large to be immersed conveniently in a tank, or 3. Touching up abraded or damaged areas on work which had been previously coated with Alodine.
Bonderite C-SO SS2 Aero (380297) is a blend of petroleum hydrocarbons so formulated to meet the basic requirements US Military specification MIL-PRF-680 Type II (Military Symbol S02). It has a narrow boiling range, is low in aromatics and has a flash point of 63oC.
Bonderite C-IC Metal Glo 6 Aero (378359) is a viscous liquid material used for the removal of oxides and corrosion from aircraft and aluminium surfaces. Bonderite C-IC Metal Glo 6 Aero (378359) removes corrosion residues, oxides, light carbon and other light soils. It is non-streaking and non-corrosive to aluminium surfaces, when used according to directions
Bonderite C-AK 5948 DPM (381643) is an alkaline, water base, blue concentrated compound formulated to effectively clean painted and unpainted aircraft exterior and interior surfaces when diluted with water.Bonderite C-AK 5948 DPM (381643) is ideally suited for use on all models of jet aircraft.Bonderite C-AK 5948 DPM (381643)is also designed to be used in immersion tanks, for dip applications.
Bonderite C-AK 5948 Aero (378343) is an alkaline, water-base, concentrated compound formulated to effectively clean painted and unpainted aircraft exterior surfaces when diluted with water or solvents. Effectively removes dirt, petroleum and synthetic oil film, grease from aircraft surfaces, landing gear, wheel wells, flaps, etc.
Bonderite C-MC 5884 (378404) is a concentrated liquid cleaner which is effective in the removal of oil, salt and solid deposits from compressor blades, guide vanes and rotors of in-service jet engines. Periodic cleaning of these components is necessary to avoid power loss, abnormal temperature increases and increased fuel consumption.
Bonderite C-MC HDF21 (1234947) is excellent for wiping down or spraying machinery and heavy equipment. It readily removes heavy oils, greases, carbonaceous soils and is ideal for general purpose industrial maintenance cleaning operations.
Bonderite C-AD CA (170087) detergent additive is a formulated blend of non-ionic and anionic surface active agents. When added to alkaline or neutral cleaning solutions, Synergic CA greatly enhances the cleaning performance and life of the cleaner.
Bonderite C-AK Sprayeze R (377370) is an off-white powder formulated to remove drawing lubes, lube oil, marking inks and shop soils from ferrous and non-ferrous alloys. Bonderite C-AK Sprayeze R (377370) is ideal for cleaning parts prior to phosphating since it helps eliminate alkaline carry-over and does not contain free caustic. Special additives are incorporated in Bonderite C-AK Sprayeze R (377370) that suppress dusting and hard caking tendencies, thus insuring Bonderite C-AK Sprayeze R (377370) remains free flowing under most severe conditions.
Bonderite C-IC 425 (169471) is a liquid, acidic heavy duty immersion cleaner for aluminium substrates. The cleaning bath made from Ridoline 425 is slightly etching and free rinsing. It effectively removes drawing lubricants and compounds and tends to maintain the original bright surface.
Bonderite C-AK Plaudit (337694) is a non-hazardous water based compound formulated as a safe general purpose cleaner for use on all surfaces. The product removes shop soils, oils, greases, road grime and lube oils from transportation, construction and drilling equipment, concrete floors, metal components, engine rooms and bilges.
Bonderite C-AK 3326G (1359833)is designed to prepare ferrous articles to receive uniform, phosphate coatings. Applied by spray, this medium to heavy duty alkaline material is usually recommended for difficult cleaning jobs, particularly C.K.D. panels with aged protective oils and waxes.
Bonderite C-AD 1523S (212974) is a multi package, low temperature, liquid cleaner formulated to prepare ferrous, zinc and aluminium surfaces to receive uniform, dense, crystalline conversion coatings. The medium to heavy-duty cleaning solution is designed specifically for use in the automotive industry. The treatment solution may be applied by spray or immersion and is very effective in removing metal working fluids and soils.
Bonderite C-AD Antifoam (169433)is a liquid defoaming agent, formulated for use in Parco Cleaner, Novaclean, Ridoline cleaner, or Bonderite, Duridine, Novaphos clean and phosphate pretreatment baths.Bonderite C-AD Antifoam (169433) effectively reduces the level of foam on the surface of freshly made-up baths or of baths operating at temperatures lower than their optimum.Bonderite C-AD Antifoam (169433) suppresses the foaming tendencies for longer periods than does kerosene or other solvents and does not decrease the effective detergent levels in the bath.
Bonderite C-AK NC4009 (1440278) is a high alkalinity liquid metal cleaner containing a high level of low foaming surfactants. Bonderite C-AK NC4009 (1440278) is suitable for spray and immersion cleaning of ferrous metals prior to phosphating, and also for cleaning and activating galvanised steel and aluminium prior to phosphating or chromate conversion.
Bonderite S-AD S1 (169815) is a liquid blend of caustic alkali and organic solvents. It contains no phenols, cresols or organic acids. It is much safer to use than similar products containing phenols. It is supplied in 2 parts: Novastrip S1 and Novastrip Additive.
Henkel Surface Technologies supplies a number of chromium containing compounds for various metal treatment procedures. From time-to-time, solutions or rinses containing these compounds may require dumping. Stringent pollution control regulations in many areas prohibit the disposal of hexavalent chromium compounds into sewage systems. This bulletin presents a simple and economical treatment process, which will provide environmentally safe waste water.
Bonderite MPT 54NC (169764) is an acidic, inorganic, liquid post treatment chemical used in immersion and spray final rinses to improve paint adhesion and to minimise underfilm corrosion and blistering. This final rinse counteracts the effect of hard water salts and leaves the phosphated surface of metals in the best condition for painting.
TURCO 6840S is a viscous, light purple liquid formulated to remove multiple coats of paints, such as baked enamels, lacquers, varnish, synthetic enamels, Koroflex, polysulphide, zinc chromate primers, epoxies and polyurethanes. TURCO 6840S paint remover clings to vertical as well as over-head surfaces and can be used on aluminium, magnesium, cadmium-plated steels and other ferrous metals.
Bonderite S-ST 5351 (377809)is a yellow, viscous paint remover developed to remove epoxy, polyurethane and similar coatings from metal surfaces at ambient temperatures. Bonderite S-ST 5351 (377809) clings to vertical and overhead surfaces and forms a surface film that helps retard evaporation and extend the working life of the stripper. TURCO 5351 should not be used on materials that are affected by chlorinated hydrocarbons.
Bonderite S-ST 5351 Thin (378409) is an amber, diphase liquid developed to remove epoxy, polyurethane and other catalysed finishes from ferrous and non-ferrous surfaces. The product contains no free acidic or alkaline constituents and is approved for use on Aluminium, Magnesium and high strength steels. Bonderite S-ST 5351 Thin (378409) should not be used on materials that are affected by chlorinated hydrocarbons.
Turco 5668 (378381) is a diphase, liquid paint remover developed without phenols, chromate and chlorinated solvents or acids to remove resistant coatings, such as polyurethanes, acrylics, epoxies and chromated primers. Turco 5668 (378381) is ideal for the removal of PRC-1560MC and PRC-1560M coatings and is not detrimental to aircraft metals, such as aluminium, titanium, magnesium, cadmium, conversion coatings, Dow coatings and ferrous alloys. Turco 5668 (378381)is supplied with a built-in non-aqueous chemical seal which retards evaporation and helps minimise drag out losses.